Edison State Community College

Bachelor of Science in Applied Science—Completion Program

  • Originating Institution: Edison State Community College
  • Target Institution and Campus: Miami University Regionals
  • Degree/Program: Bachelor of Science in Applied Science, Major: Robotics Engineering Technology

For students entering Fall 2020 and after

Updated: Spring 2022


This Bachelor of Science in Applied Science Completion Program is designed for students who have completed an associate degree in Mechanical, Electrical, Electro-Mechanical or similarly titled engineering technology programs. Graduates from other Engineering Technology programs will also receive favorable credit transfer. Graduates from other Engineering Technology programs will also receive favorable credit transfer. Through this program you can complete your BS degree by completing two-years of additional credit hours beyond your associate degree.
Further information is available through http://www.miamioh.edu/regionals/ent.

This articulation is meant to be a guide only. Your final degree requirements are established upon matriculation to Miami and are detailed in your degree audit report (DAR) provided by Miami. Work closely with a Miami advisor (listed below) to clarify final requirements. Students entering this program must meet all admission requirements available at http://www.miamioh.edu/regionals/admission/transfer-students for transfer students or in the Miami Bulletin. For students who graduated from high school after 1985, these requirements include a foreign language in high school (two years) or college (one year). Students who do not meet these requirements at admission will still be admitted but must make up any deficiencies prior to graduating from Miami.

There are four areas of program requirements. About one-half of these requirements will be met while completing your associate degree. In addition, students must meet the general requirements for graduation from Miami which include a minimum of 30 credit hours taken from Miami and 12 of the last 30 credit hours must be taken from Miami. Students are also required to have a PC laptop.

Requirements Summary

  1. Complete your associate degree in Electrical, Mechanical, Electro-Mechanical or similarly titled Engineering Technology program at your current college.

  2. Complete the Ohio Transfer 36 at your institution. This Module is available at Workbook: Ohio Transfer36 Approvals.

  3. Click on your college. Once complete, have the registrar at your college notate completion in your transcript: “Ohio Transfer Module Complete” and send the revised transcript to Miami. Advising for this module is available at your college. See the registrar or advising office.

  4. Complete general education requirements specified by the Engineering Technology (ENT) department. (*Included in the Ohio Transfer 36)

Program Requirements
Required Course From Miami

Acceptable Edison State Community College Transfer Credit**

* Included in the Ohio Transfer Module (OTM)

ENG 111, One year of Freshman English College I Composition or

ENG 109 College Composition for Second Language Writers

ENG 121S* English Composition I

ECO 201 Microeconomics or ECO 202 Macroeconomics

ECO 221S* Microeconomics

or ECO 222S* Macroeconomics

STC 135 Intro to Public Expression and Critical Inquiry or

STC 136 Intro to Interpersonal Communication

COM 121S* Fundamentals of Communication

EGS 215 Workplace Writing or

ENG 313 Technical Writing

ENG 125S Technical Writing

PHY 161 Physics for Life Sciences with Lab I or

PHY 191 General Physics with Lab I

PHY 121S* Physics I

PHY 162 Physics for Life Sciences with Lab II or

PHY 192 General Physics with Lab II

PHY 122S* Physics II

CHM 141 College Chemistry (3) and

CHM 144 College Chemistry Lab (2)

CHEM 121S* General Chemistry

MTH 151 Calculus I MAT 251* Calculus I
MTH 251 Calculus II MAT 252* Calculus II
Approved Intercultural Perspectives Elective (Online Options)

SSV113S Introduction to Social Welfare or

Approved Intercultural Perspectives Elective

5. Complete Engineering Technology (ENT) core courses listed below. You should have taken some of these in your associate degree program. Calculus I must be completed prior to starting Miami courses.

Engineering Technology Core Courses
Required Course From Miami

Acceptable Edison State Community College Transfer Credit**

* Included in the Ohio Transfer Module (OTM)

ENT 135 Computer-Aided Drafting [OET012 Computer Aided Design]

EGR 110S Print reading and Sketching and MET 130S


CSE 153 Introduction to C/C++ Programming or similar course

CIS 223S C++ Programming

ENT 192 Circuit Analysis I [OET001 DC Circuits]

ELT 110S Circuits I

ENT 193 Circuit Analysis II [OET003 AC Circuits]

ELT 210S Circuits II

ENT 196 Electronics [OET005 Electronics]

ELT 121S Electronic Devices

ENT 271 Mechanics I: Statics [OET007 Statics]

MET 125S Applied Engineering Statics

ENT 272 Strength of Materials [OET008 Strength of Materials]

MET 212S Applied Strength of Materials

ENT 293 Digital Systems [OET002 Digital]

ELT 141S Digital Electronics

ENT 296 Programmable Logic Controllers

ELT 151S Programmable Logic Controllers

MTH 245 Differential Equations

MTH 231S Differential Equations or take from Miami

STA 261 Statistics or STA 301 Applied Statistics ***

MTH 125S or Take from Miami

ENT 301 Dynamics ***

MET 211S Dynamics, B or better

ENT 311 Process Control Interface Design ***

Take from Miami

ENT 313 Introduction to Robotics Systems

Take from Miami

ENT 316 Project Management ***

Take from Miami

ENT 401 Computerized Instrumentation ***

Take from Miami

ENT 413 Industrial Robotics Lab

Take from Miami or ELT 233S Servo Systems and Robotics from Edison State

ENT 417 Integrated Robotics System Engineering Take from Miami
ENT 418 Electromechanical Control Systems *** Take from Miami
ENT 497 Senior Design I *** Take from Miami
ENT 498 Senior Design II *** Take from Miami

***Distance Courses Offered Via IVDL and/or WebEx from Miami. Calculus I must be completed prior to starting Miami courses.

**Transfer Equivalencies within ENT program ONLY

To apply for this program: http://www.MiamiOH.edu/regionals/apply

For tuition information: https://MiamiOH.edu/onestop/your-money/tuition-fees/regional-campuses/index.html

For more information, contact:

Edison State Community College:
Tom Looker-Associate Professor
Email: tlooker@edisonohio.edu
Phone: 937-778-7943

Dr. Mert Bal, Chair and Associate Professor & Coordinator of EMET Program
Email: balm@MiamiOH.edu

Dr. Meenakshi Narayan Assistant Professor and Coordinator of RET program
Email: narayam3@MiamiOH.edu

Sarah Wooten, Enrollment Advisor and Distance Coordinator
Email: sarah.wooten@MiamiOH.edu